Warning Cookies are used on this site to provide the best user experience. If you continue, we assume that you agree to receive cookies from this site. OK

I n n o v a t i v e   M a r i n e   P r o d u c t s   f o r   t h e   I n f o r m e d   S e a f a r e r   -   S i n c e  1 9 9 5

Call Us at 952-920-8500 M-F 9A-5P CST

Please Note: Updated Monday, April 6, 2020  We are open for business as usual. Well, mostly usual. We hold and ship inventory locally as well as directly from manufacturers and from some marine distributors. We are doing our best to reflect inventory that is actually available, but inventory updates are slower than usual due to the changing work situations for all business. Additionally, we now have started to see longer than normal backorders from manufacturers. We recommend that if you need a product not to wait until the last minute to order, as inventory may be gone for a substantial period of time once they go on backorder. International orders may also take longer than normal to ship. We are sorry for these delays.

Webasto DBW 2015 Hydronic Marine Boat Heater Kit with Surewire Water EZ Install Board

List price: $7,315.97
You save: $366.97 (5%)
30 days

Webasto DBW 2015 Hydronic Marine Boat Heater Kit with Surewire EZ Install Board

For additional kit details, click here.

The DBW 2015 is designed for larger sailboats ranging from 48 to 52 feet and powerboats ranging from 47 to 50 feet (depending on make and model). This unit is a diesel-fired boiler that is available in 12 and 24 volt and is rated at 45,000.

The DBW 2015 is a water heater designed to heat a coolant loop run throughout the boat with a system of fan heaters that will blow hot air over coils flooded with coolant. In larger boat applications, water heat is almost a necessity due to the fact that air heaters will not have the airflow to heat the entirety of the boat at an even level. A coolant heater heats the coolant evenly, thus heating the entire boat at an even rate. Other benefits of water heaters are added applications such as domestic water heat and engine heat. The DBW 2015 can be plumbed through existing domestic hot water systems replacing the engine as a heat source. The engine can be then used to heat the entire heating system by way of a water-to-water heat exchanger.

The DBW 2015 can be plumbed in such a way that when it is operational, the unit will heat domestic hot water. This can be done by plumbing one of the heater loops through an existing hot water heater, or by installing an Everhot heating system. The Everhot is an on-demand domestic water heater that will provide domestic hot water as long as the heater is up to temperature. Contact Great Lakes Marine Specialties (NavStore) for more information on the Everhot system.

The engine can be used as well to heat the entire system as if the DBW 2015 were running. This can be accomplished by installing an optional water-to-water heat exchanger in the system, and a switch to run the system pump but not the heater. In this configuration, the engine heats its loop through the heat exchanger and the heat exchanger heats the system. The heating system will perform in the same parameters as if the heater were running. A separate switch can be installed with a separate pump to pre-heat the engine. The pump will move the water in the engine loop back through the engine block when the heater system is up to temperature. This will preheat the block before starting the engine and will provide an easy start every time without the need for chemicals.

The DBW 2015 system can be wired in such a way that it can be controlled by internal temperature of the boat. It has the ability to be zoned into an unlimited amount of zones based on your needs. In this application, multiple thermostats are installed in each "zone" of the boat controlling the operation of the heater. A zone can be staterooms, heads, saloons, etc. If any zone is calling for heat, the thermostat will have the heater and the nearby fan heater run until the cabin is up to temperature. Once all zones are up to temperature, the heater and fan heaters will be turned off. When heat is needed again in any zone, the fan heaters and eventually the heater itself will be turned on.

As with everything in the boating world, placement is very important. A clean, dry location should be chosen for the mounting of the DBW 2015. Once a spot is chosen, it must then be checked against the parameters of the heater. The installation manual will provide specifics, but major limitations such as the exhaust should be considered. The exhaust should be vented as high and as far aft as possible with the aft transom being the ideal place for going through the hull. The DBW 2015 has a maximum run of 12' and may only have 270° or less in bends. The unit should also have adequate room for maintenance of the heater and related components that must be located near the unit. Also take into consideration the limitations of the fuel, electrical and coolant systems. Contact Great Lakes Marine Specialties (NavStore) or consult the installation manual for further specifications on mounting.

As mentioned before, placement of the exhaust thru-hull is very important to heater installation. The DBW 2015 uses a 1 1/2" exhaust pipe and thru-hull. The thru-hull must be installed in a place where it is free of seawater and where there is a limited possibility of contact with any limbs of passengers on your boat. The aft transom is the ideal position for the thru-hull, but it is not always possible to reach. In this case, a spot as far aft as possible should be chosen.

Once limitations for the heater have been considered, locations to mount the other parts of the heating system should be chosen. Aside from hose and fan heaters, most other system components (such as the system pump, manifolds, domestic water heater and so on) can be mounted near the heater out of the way. One component is in most cases very tricky to mount: the expansion tank. The expansion tank in the water system must be above everything else in the system. If you wish to put a fly bridge heater on your fly bridge, the expansion tank must be above the heater. This is to provide head pressure for the water pump and to prevent air locks in the system. This is an inconvenient specification, but if your heater is to perform properly, it must be followed.

Once space for all of the system components has been chosen, fan units for your cabins must be sized and have space provided for them. Each cabin has different needs for heat depending on use, layout, amount of windows, and so on. To figure BTU for each cabin, take the cubic footage (length x width x height) and multiply it by 15. This will give you an approximate rating for that space, favoring the high side. If the space is well insulated and has no windows, perhaps a factor of 12 can be used.

Once BTU requirements have been figured, different models of fan heaters can be chosen by shape, capacity or use. See the attached information on fan heaters to choose the right fan heaters for your spaces. Each fan heater is normally rated to 7,000 BTU or 14,000 BTU depending on model. In some cases a space may not need 7,000 BTU, but to have heat it must have a fan heater. There are fan heaters that can be split between two spaces and divide the heat. Another method is to merely have the fan controlled by thermostat. Once the smaller space is up to temperature, the unit will shut off.

Once all models have been chosen for each space, subtract their rating from the 45,000 BTU of the DBW 2015. More fan heaters than the rated BTU of the heater can be installed but for the unit to operate properly only 45,000 BTU of fan heaters should be in operation.

With this information, heater choice for your boat should be a bit easier (or perhaps harder if you cannot meet some of the specifications listed). If you have any further questions on installation or operation, please contact Great Lakes Marine Specialties (NavStore) for more information.

For additional kit details, click here.

Webasto DBW2015 50,000 Btu Hydronic Marine Heater with Surewire Easy Interface Board

12v With Marine Installation Manual & Surewire Kit
Heat Output: 50,000 btu
Fuel Consumption: .4 gal/hr
Voltage: specify 12 or 24 volt DC
Power Consumption (12v): Full: 7.1 amps
Dimensions: L 23 x W 8 1/16 x H 11 5/8 (584mm x  205mm x 295mm)
The DBW 2015 hydronic heater offered by Webasto will heat up to a 52 foot sailboat or a 50 foot powerboat. The DBW 2015 utilizes 1" water hose to deliver heated coolant to dual 3/4" zones of fan heaters throughout the boat. The DBW 2015 uses a 1-1/2" rigid exhaust system, and a 1/4" supply (no return necessary).

The SMS installation kit features:

Surewire Water Easy Installation Interface

The Surewire Water board puts all electrical connections into one place making installation and troubleshooting of your heater easier than ever before. The Surewire Water is for all Webasto Water heaters.

Features include:Ready for hassle free thermostat wiring; up to four zones!

  • Domestic water heater control wiring
  • Easy to add engine heat control
  • Hour meter to track run time of the heater
  • Comes with protective cover and backing plate
  • Breaker protection of heater in one convenient place